Terasun Europe
Stacked Terasun TSM lightweight cement boards showing the EPS-granule core and fibreglass mesh surface
Specifications · Documents

Terasun TSM Cement Board: Specifications, Composition, and Technical Documentation

Verified product data for Terasun TSM Cement Board in one place: composition, dimensions, weight, European technical documentation, environmental declaration and fire classification.

Composition

Cement-based

Cementitious matrix, glass fiber mesh, water, EPS granules — not an MgO/Sorel board

Weight

9.96 kg/m²

12 mm board, 1200×2400 mm — about 28.7 kg per 2.88 m² sheet

Thickness

3–30 mm

Supplier range; standard 1200×2400 mm, lengths up to 3000 mm

Carbon footprint

7.49 kg CO₂-eq/m²

GWP-total A1–A3, 12 mm board (EPD-IES-0018268)

What Is Terasun TSM Cement Board?

TSM Cement Board is a lightweight cement-based construction board manufactured by Zhejiang Terasun Air Duct Co., Ltd. According to the product documentation, it is composed of a cementitious matrix, fiberglass mesh, water, and lightweight EPS (expanded polystyrene) granules. It is important to note that this is not a magnesium-based (Sorel/MgO) cement board—a common point of confusion in the market. For project documentation, it is essential to correctly specify the composition as cement-based rather than magnesium-based. For architects, engineers, and distributors searching for “TSM Cement Board technical data,” this page consolidates verified product information in one place, including composition, dimensions, weight, European technical documentation, environmental declarations, and fire classification—with links to the relevant source documents.

Composition, Dimensions, and Weight of a 12 mm Board according to the EPD

For a 12 mm thick board, EPD-IES-0018268 specifies the following per 1 m²: cement (binder)—the primary component by mass; glass fiber mesh—0.300 kg; water—0.996 kg; and EPS granules—0.143 kg; for a total mass of 9.960 kg/m². These figures pertain to the declared functional unit as defined in the EPD. The EPD covers a board measuring 1200 mm in width and 2400 mm in length, with a surface area of 2.88 m² and a weight of approximately 28.7 kg—allowing it to be handled and installed by two people without the need for lifting equipment. Data for the 12 mm board cannot be scaled linearly to other thicknesses; such values must be verified against the manufacturer’s current technical data sheets.

Composition per 1 m² of 12 mm board (EPD-IES-0018268)
Per 1 m², 12 mmMass
Cement (binder)Primary component by mass
Glass fiber mesh0.300 kg
Water0.996 kg
EPS granules0.143 kg
Total9.960 kg

Available Thicknesses and Formats: from 3 to 30 mm, Lengths up to 3000 mm

According to the supplier, TSM Cement Board is available in thicknesses ranging from 3 to 30 mm (including 3, 6, 8, 10, 12, 16, and 20 mm, with other thicknesses available upon request). The standard sheet format is 1200×2400 mm; boards can also be manufactured in lengths of up to 3000 mm. Non-standard dimensions can be discussed upon inquiry with Terasun Europe.

  • 3 mm
  • 6 mm
  • 8 mm
  • 10 mm
  • 12 mm
  • 16 mm
  • 20 mm
  • others on request

The thickness range of 3–30 mm and lengths of up to 3000 mm are based on information provided by the supplier, rather than on data from EPD-IES-0018268; the board analyzed in the EPD has a thickness of 12 mm and a format of 1200×2400 mm. The availability of specific thicknesses and lengths, as well as minimum order quantities, are confirmed at the time of order arrangement.

European Documentation: ETA, DoP, and CE Marking

ETA 24/0895 is a European Technical Assessment, issued in conjunction with the Certificate of Constancy of Performance (CE 1023-CPR-1565 P). The scope of this assessment is defined by EAD 350142-00-1106, a harmonized document for the assessment of fire-protective boards and products. The existence of an ETA does not imply certification for every possible application of the TSM product; its scope is strictly defined by the content of the document and the specific product type. A Declaration of Performance (DoP)—TRS-20250610F—is also provided for the product. During the design and procurement phases, it is essential to verify that the product identifier, thickness, and declared performance characteristics match the specific batch being supplied. Furthermore, the CE marking does not signify that any arbitrary construction system incorporating the board has been tested as a complete, integrated assembly.

Environmental Product Declaration (EPD) and Carbon Footprint

EPD-IES-0018268 has been prepared in accordance with EN 15804+A2. For 1 m² of the 12 mm board under study, the GWP-total value for stages A1–A3 is 7.49 kg CO₂-eq. This figure applies specifically to the product studied and the system boundaries defined in the EPD; it cannot be extrapolated to other thicknesses, nor can it be directly compared with EPDs from other manufacturers without first verifying the comparability of the functional units, system boundaries, and calculation methodologies (e.g., the specific version of the EN 15804 standard used).

Fire Classification: Reaction to Fire and Fire Resistance of a Partition Wall

Report FIRES-CR-284-25-AUPE confirms the E120/EI90/EW120 classification (per EN 13501-2:2023) for a specific non-load-bearing, insulated partition wall. This assembly features C100×45×0.6 mm steel profiles, 12 mm TSM boards on both sides of the frame, a stud spacing of up to 600 mm, and 100 mm thick mineral wool insulation. A separate document from Intertek, based on EN 12467:2012, assigns a reaction-to-fire class of A1 to the 12 mm tested specimen. Note that the material class (A1) and the fire resistance rating of the assembly (E120/EI90/EW120) are distinct metrics: the former describes the individual board, while the latter refers to the complete, assembled partition wall. Further details can be found on the dedicated fire safety page.

Application and Selection of Boards Based on Intended Use

TSM boards are suitable for exterior and interior cladding, wet areas, and fire-protection applications. Each specific use requires a separate assessment to ensure that the fasteners, finishes, waterproofing, or sub-framing systems are compatible with the project requirements. Product certifications (such as ETA, CE, DoP, EPD, or fire test reports) do not automatically validate the entire completed system. There is no single, universal board that suits every purpose: for facades, considerations include wind load and fastening requirements; for wet areas, compatibility with waterproofing is essential; for fire-rated partitions, strict adherence to the FIRES-CR-284-25-AUPE assembly specification is required; and for LGSF (light-gauge steel framing) construction, the weight of the board and the fastening pattern are key factors. Further details for each application can be found in the sections dedicated to Facades, Wet Areas, Fire Safety, and LGSF.

For Architects and Engineers: Specification Clause

When including TSM Cement Board in project specifications or tender documentation, it is recommended to specify the product with the following full set of references:

  • Name: Terasun TSM Cement Board—a cement-based board incorporating glass-fiber mesh and EPS granules (distinct from MgO/Sorel-type magnesium oxide boards).

  • Thickness and Dimensions: Available in a range of 3–30 mm (per supplier specifications); standard format is 1200×2400 mm, with lengths up to 3000 mm available upon request. For a 12 mm board, the mass is 9.96 kg/m², as verified by EPD-IES-0018268.

  • Certification and Assessment: CE 1023-CPR-1565 P; ETA 24/0895 (assessed according to EAD 350142-00-1106); DoP TRS-20250610F.

  • Environmental Product Declaration (EPD): EPD-IES-0018268 (EN 15804+A2); GWP-total (A1–A3) is 7.49 kg CO₂-eq/m² for a 12 mm board.

  • Fire Performance: Reaction to fire class A1 for a 12 mm specimen (tested by Intertek, EN 12467:2012); for partition assemblies, ratings of E120/EI90/EW120 apply (per FIRES-CR-284-25-AUPE).

  • European Supplier: Terasun Europe (via PlanX Oy); contact: info@terasun-europe.eu.

Documents, Pricing, and Delivery

For technical specifications, please request the ETA, DoP, EPD, and fire classification report from Terasun Europe. When publishing or sharing these files with third parties, please adhere to the reproduction terms stipulated by the document copyright holders (specifically regarding the FIRES report). Pricing and lead times are determined on an individual basis; for wholesale supplies, see Distributors and Wholesale. For commercial inquiries, please specify:

  • Country and project location
  • Required thickness and dimensions
  • Quantity of sheets
  • Desired delivery timeline

Frequently Asked Questions About the Technical Specifications of TSM Cement Board

What is the TSM lightweight cement board made of?

According to the EPD, 1 m² of 12 mm board consists of a cementitious matrix (the primary component), 0.300 kg of glass fiber mesh, 0.996 kg of water, and 0.143 kg of EPS granules, with a total mass of 9.960 kg. This is not a magnesium oxide (MgO/Sorel) board.

What thicknesses and lengths are available for TSM Cement Board?

The supplier offers thicknesses ranging from 3 to 30 mm. The standard format is 1200×2400 mm; lengths up to 3000 mm are also available, and custom dimensions can be arranged upon request. The EPD-IES-0018268 specifically covers the 12 mm 1200×2400 mm board.

Does Terasun hold a European Technical Assessment (ETA) and a Declaration of Performance (DoP)?

Yes: it holds ETA 24/0895 and DoP TRS-20250610F. When designing, it is necessary to verify the scope of the ETA and ensure that the DoP corresponds to the specific products being supplied.

Does the ETA cover a complete facade system?

No: the scope of the ETA applies to the board as a product, not to the facade sub-construction system—that requires separate documentation.

Is TSM cement board suitable for facades, bathrooms, and LGSF (Light Gauge Steel Framing) structures?

The material can be used for all three applications as part of a designed system, provided that the sub-construction, fasteners, and finishes are verified. Further details can be found on the “Facades,” “Wet Rooms,” and “LGSF” pages.

Request a Consultation and Technical Documentation

Terasun Europe is a division of PlanX Oy responsible for the supply of TSM Cement Board in Europe. Please email info@terasun-europe.eu and specify the project country, type of construction, board thickness, and estimated quantity. We will assist you in selecting the appropriate technical documentation (ETA, DoP, EPD, fire resistance report) for review in the context of your project.